Showing posts with label Fuse. Show all posts
Showing posts with label Fuse. Show all posts

Thursday, 21 September 2017

Fuse part 5

#Channel2

Previous part1 part2 part3 part4
Fuse Characteristics
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The action of fuse is based upon the heating effect of current. Larger the current, the more rapidly the fuse will blow and save their circuit and equipment from unnecessary problem. It has #Inverse_time_characteristics (When large current flows, It takes less time to melt than for a small Current). This characteristics helps it to use in overload purpose.

#Selection_of_fuse: • For Short circuit protection, the fuse elements must be with a good margin for temporary overloads.
• Speed of operation- It depends upon how much current flows through it and depends upon the material of fuse element.
The operating time is not fixed, but decreases as current increases(Inverse Time Characteristics)
• SemiConductor devices need a fast blow or ultra fast blow fuse because a small excessive current can damage the device easily. Normally fast blow fuses are the most general purpose fuses.
•  Time delay fuse can continue with a small high current for a while. (It is used in motor)
• The fuse element must not be damaged by minor harmless surges of current and must not oxidise or change its behaviours after use for several years.
• It should withstand the transient surge due to switching in and out.

#Difference_between_fuse_and_CircuitBreaker
¡) fuse - fast operation. (0.001 or 0.002 sec)
   CB - comperatively slow. (0.1 to 0.2 sec)

¡¡) fuse - when it melts, you must change it
    CB- you can reset it, when fault clears totally.

¡¡¡) fuse is cheap and possibly of failure is Nil.
      CB is expensive and a small defect in trip mechanism can damage it fully.
Like us on facebook.

Fuse Part 4

#channel2

[to read previous parts part1 part2 part3]
#Terms related to fuse

#Rated_Current : It is the maximum current which the fuse can carry without any heating or melting. It depends upon fuse element material,temperature rise and deterioration of the fuse by oxidation.
#Fusing_Current : It is the maximum current at which the fuse elements melts and disconnects the circuit. It is more than the rated current. If rated current is 5A, then 5A can easily flow through the fuse without heating but fusing current will be more than 5A.
if fusing current = I
k = constant depends upon metal of wire
d= diameter of fuse element
then, I = k.  d to the power (3/2)

#Fusing_factor: Ratio of fusing current to rated current.
for rewirable fuse it is 2 for copper.

#Prospective_Current: r.m.s value of the first loop of the fault current is called prospective current.

#Cut_off_Current: value of current reached before the fuse melts. Depends upon ¡) prospective current
¡¡) current rating of the fuse.

#pre_arcing_time: It is the time between time of fault occurs and instant of fuse melts.( 0.001 sec)

#arcing_time: it is the time taken from the instant of arc started to the instant of arc extinguished.

#BreakingCapacity_or_RupturingCapacity: It is the maximum current that can safely be interrupted by the fuse. This should be higher than the prospective current. Fuses for high voltage equipment, upto 115000 volts, are rated by the total apparent power(MVA) of the fault level in the circuit.

#Melting_ i square t
- is propotional to the total energy required to begin melting the fuse element.
#Clearing_ i square t
- is propotional to the total energy let through by the fuse when clearing a fault.
#Rated voltage- Rated voltage should be higher than the maximum voltage source. A fuse rated at 32 volts would not reliably interrupt current from a voltage source of 120 volts. If it is used, an arc is formed and plasma inside the glasstube(if it is glass tube fuse) may continue to conduct current.
Like us on facebook.

Fuse Part 3

#channel2

[ to read previous parts
Click part 1 & part 2]

#Desirable_Character_of_fuse_element.
   • low melting point
             - because you would like a wire that responds to current flow without heating up too much thus avoiding a fire hazard.
  •   High Conductivity.
  •   Free from deterioration due to oxidation.
  •   Low cost.
Low melting point material comes with high specific resistance and with higher mass.
High melting point material comes with low specific resistance and with low mass.
Oxidation of fuse element(e.g. copper and iron) tends to generate an outer layer which may be strong enough to support the metalic core of fuse element when it is in molten state.
Part1 Part2  Part3 Part4  Part5
Like us on facebook.

MCB

Miniature Circuit Breaker